We have unearthed this great article involving How to Install a Bathtub Yourself listed below on the net and thought it made perfect sense to relate it with you over here.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bath tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is conveniently available, the job can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will require a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is better to think about using one before you start. Chances are you might require a professional plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently acquired a new bathtub and also don't need to transform the setup of your previous supply of water pipes.
Your devices and also material checklist need to comprise the following:
Getting ready for the Installment
To start with, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water supply and also check all joints as well as new pipework for leakages and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will resolve it into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in place with the producer supplied backnut. When the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former type must be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our part on Installing A Bathtub. Thanks so much for taking the time to browse our short article. Do you know about another individual who is truly interested in the topic? Do not hesitate to promote it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Visit Homepage